1.出現偏焊問題：可能為焊接的位置不正確或焊槍尋找時出現問題。這時候，就要考慮TCP（焊槍中心點位置）是否是正確的，并且加以調整。假如頻繁出現這種情況就要檢查一下機器人各軸的零位置，中心校零予以修正。

1. Deviation welding problem: It may be due to incorrect welding position or problems with the welding gun during searching. At this point, it is necessary to consider whether the TCP (center point position of the welding gun) is correct and make adjustments. If this situation occurs frequently, it is necessary to check the zero position of each axis of the robot and correct it by centering.

2.出現咬邊問題：可能為焊接參數選擇不當、焊槍角度或焊槍位置不對，可適當調整。

2. Edge biting problem: It may be due to improper selection of welding parameters, incorrect welding gun angle or position, which can be adjusted appropriately.

3.出現氣孔問題：可能為氣體保護差、工件 的底漆太厚或者位置不對，可適當調整。

3. Pore problem: It may be due to poor gas protection, too thick primer on the workpiece, or incorrect position, which can be adjusted appropriately.

4.飛濺過多問題：可能為焊接參數選擇不當、氣體組成部分原因或焊絲外審長度太長，可適當調整機器人功率的大小來改變焊接參數，調節氣體配比儀來調整混合氣體比例，調整焊槍與工件的相對位置。

4. Excessive splashing problem: It may be due to improper selection of welding parameters, gas composition, or excessive length of welding wire. The robot power can be adjusted appropriately to change the welding parameters, the gas proportioner can be adjusted to adjust the mixed gas ratio, and the relative position of the welding gun and workpiece can be adjusted.

5.焊縫結尾處冷卻后形成一弧坑問題：可編程時在工作步中添加埋弧工作，可以將其填滿。

5. The problem of forming an arc crater after cooling at the end of the weld seam: When programmable, adding a submerged arc work in the work step can fill it up.

優點：

Advantages:

1，保修3年（本體,控制箱,示教盒,操作盒,控制電纜）;

1. Warranty for 3 years (body, control box, teaching box, operation box, control cable);

2，全中文操作界面,簡單易懂,同時可支持6種語言選擇;

2. The full Chinese operation interface is simple and easy to understand, and can support 6 language choices;

3，工作半徑長,標準焊接機器人工作半徑可達1.4米或者2米(不包含焊槍);

3. The working radius is long, and the standard welding robot's working radius can reach 1.4 meters or 2 meters (excluding the welding gun);

4，運動速度高,高可高于同等其他將機器人40%個軸運動速度分別是210°/S,190°/S,210°/S,210°/S,420°/S,420°/S,600°/S;

4. The motion speed is high, which can be higher than other robots of the same level. The motion speeds of 40% of the axes of the robot are 210 °/S, 190 °/S, 210 °/S, 210 °/S, 420 °/S, 420 °/S, and 600 °/S, respectively;

5，防碰撞功能，焊槍防碰撞傳感器，伺服防碰撞傳感器；

5. Efficient anti-collision function, welding gun anti-collision sensor, servo anti-collision sensor;

6，防塵，防塵等級大IP54級別；

6. Efficient dust prevention, with a dust prevention level of up to IP54;

7，電纜內置，有效提高第6軸工作范圍（B4機器人獨有，其他機器人不具備）；

7. Built in cable, effectively improving the working range of the 6th axis (unique to B4 robots, not available to other robots);

8，內置PLC，可以節省外部PLC(I/O點64個)；

8. Built in PLC, which can save external PLC (64 I/O points);

9，外部軸同步協調功能，可以在示教盒上操作外部軸，使機器人和外部軸同步動作，來完成復雜焊縫的焊接；

9. External axis synchronization and coordination function, which can operate the external axis on the teaching box to synchronize the robot with the external axis and complete the welding of complex welds;

10，多種方式鏈接區域網，I/O接口，DeviceNet,CC-Link……

10. Multiple ways to link regional networks, I/O interfaces, DeviceNet, CC Link

11，焊接特性自動調整功能，根據桿伸長長度和使用環境不同，自動調整焊接特性值，使實際焊接電流、電壓與設定值一致；

11. Automatic adjustment function for welding characteristics, which automatically adjusts the welding characteristic values based on the elongation length of the rod and different usage environments, so that the actual welding current and voltage are consistent with the set values;

12，電弧監控功能，示教盒上能夠?qū)附与娏?，焊接電壓，送絲負荷等進行監控，與DL350Ⅱ鏈接時，還可監控飛濺抑制率；

12. Arc monitoring function, the teaching box can monitor welding current, welding voltage, wire feeding load, etc. When connected to DL350 II, it can also monitor the splash suppression rate;

13，斷弧再起功能，傳統機器人焊接過程發生斷弧，機器人會緊急停止，我們機器人可以自動恢復到預先設定的再啟位置和再啟次數等操作；

13. Arc break and restart function. In the traditional robot welding process, if an arc is broken, the robot will stop urgently. Our robot can automatically restore to the pre-set restart position and number of restarts, and other operations;

本文由工業機器人友情奉獻.更多有關的知識請點擊:http://www.szjwky.cn真誠的態度.為您提供為的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

This article is dedicated by industrial robots. For more related knowledge, please click: http://www.szjwky.cn Sincere attitude. We will provide you with comprehensive service. We will gradually contribute more relevant knowledge to everyone. Stay tuned